MODIFI3D Print Finishing Tool


MODIFI3D Print Finishing Tool

The MODIFI3D Print Finishing Tool is a heated tool which has 4 specially coated different interchangeable tips, designed to finish, repair and modify your 3D printed parts. The MODIFI3D Print Finishing Tool has been developed to replace all the sanding, scraping and snapping that is needed to finish off your 3D printed parts. The MODIFI3D Print Finishing Tool works with PLA, ABS and other 3D Printing materials. The MODIFI3D Print Finishing Tool is shaped just like a pen, this makes it comfortable and easy to use, this optimises control so you can obtain the best results whilst using the tool. It will take just 15 seconds to reach a temperature of 300C and just 30 seconds to cool back down.

MODIFI3D Print Finishing Tool 4 Interchangeable Tips:

Cutting and removing sections including the removal of supports, brims and rafts from your 3D print.

Great for clearing small holes and features or for detailed layer refinements in hard to reach places.

General purpose tip for larger internal features and holes. Can even be used for making holes after printing.

Perfect for removing stringing and imperfections from inside holes or recesses. Can also be used to blend surfaces where blobs have appeared.

More Information

Tech Specs

Features: 900-0001A
4 interchangeable tips: Needle, knife, scoop and point tips.
Rapid heat up in less than 15 seconds.
Sleep mode if not used for 25 seconds.
Simple and easy to use.
Lightweight and compact.
Touch switch and indicator light.
USB powered (USB 2.0 or USB 3.0).
Basic stand included.
Specifications: 5V 8W
Size: 15mm (0.6") x 117mm (4.6") excluding tips
Weight: 120g (4.3 oz)
Cable: 1.5m (59") long to USB A plug
Heats up to 300ºC (572ºF) in less than 15 seconds.
Maximum temperature of 420-450ºC (788-842ºF)
FAQ's: Modifi3d Is Not Heating up
If possible try another USB socket. A couple of USB hubs and wall adaptors do not provide enough power for MODIFI3D to operate correctly.
We recommend using the most common USB 2.0 or USB 3.0 ports with MODIFI3D. Also ensure that your USB port is below 1A as higher may stop the "sleep" mode from working correctly.
Modifi3d Is Not Reaching 450ºC (842ºF)
After touching the metal switch MODIFI3D will automatically heat to around 300ºC (572ºF). However to increase the temperature to 420-450ºC (788-842ºF) you must continue to touch the metal switch until the required temperature is reached.
When the switch is released MODIFI3D will begin to cool and after 25 seconds go into sleep mode (light will go out and the tip will cool).
Modifi3d Will Not Go Into "Sleep" Mode
MODIFI3D will automatically sleep after not being used for 25 seconds. However the tool will not sleep (and continue heating up to 420-450ºC) if an incompatible USB port is used. These can include some USB hubs and wall plug adaptors, for example Apple iPad and iPhone wall adaptors are not compatible.
We recommend using the most common USB 2.0 or USB 3.0 ports with MODIFI3D but if you are unsure check that your USB port is below 1A.
The On/Off Switch Isn't Working
The touch switch does not have an "off" function. The tool will automatically sleep after not being used for 25 seconds.
Gently touch the switch to activate or wake MODIFI3D.
Always unplug the USB if MODIFI3D is not being used.
The Modifi3d Button Will Not Depress
The button is actually a touch switch and does not depress. DO NOT try to push/press/depress the switch as you could damage the tool. To activate or wake MODIFI3D just gently touch the switch.
Write Your Own Review
You're reviewing:MODIFI3D Print Finishing Tool

Whats in the Box

  • 1 x MODIFI3D Tool
  • 4 x Interchangable Tips (Knife, Scoop, Needle & Point)
  • 1 x USB Power Cable
  • 1 x Basic Stand