THE K8™ TPU Air – Temperature-Controlled Foaming TPU Filament
THE K8™ TPU Air is a 1.75 mm thermoplastic polyurethane filament that can be printed in non-foamed or foamed states. By changing the printing conditions, users can explore different material densities, softness levels and surface textures using the same filament. Kexcelled's technical data sheet reports a density of 1.14 g/cm³ and Shore hardness of 90A in the non-foamed state, compared with 0.57 g/cm³ and 69A at its specified 200% foaming condition.
The material is relevant to the development of lightweight cushioning, flexible structures, footwear components and tactile products. Actual part characteristics depend on the print settings and design.
Four Key Material Features
Genuine Kexcelled photographs illustrate the different processing states and example applications. Performance figures below are drawn from the manufacturer's technical data sheet rather than inferred from the photographs.
Feature 01
One Filament, Different Printing States
Temperature-responsive foaming allows designers to compare a firmer, non-foamed TPU state with lighter, softer foamed structures. Print a small calibration piece to establish the effect on your specific printer.
Feature 02
Lower Density for Lightweight Parts
The manufacturer's TDS measures a reduction in material density from 1.14 to 0.57 g/cm³ between its stated non-foamed and 200% foaming conditions. Final part weight also depends on part geometry, shell thickness and infill.
The figures printed within this Kexcelled sample photograph refer to those particular demonstration pieces, not the bulk-material density values in the TDS.
Feature 03
Cushioning and Flexible Design Possibilities
Foaming changes the tested hardness and density of TPU Air, making it a material to evaluate for flexible contact areas, cushioning structures and insole prototypes. Geometry, temperature and print orientation should be assessed for the intended application.
Feature 04
Distinctive Tactile Surface
Under suitable foaming conditions, Kexcelled describes a soft, fabric-like surface appearance. The finish can be relevant to consumer-product prototypes, flexible accessories and other parts where texture matters alongside mechanical behaviour.
Material Performance: Non-Foamed vs Foamed
Typical manufacturer-reported values at the two stated conditions, taken from TDS KT114, revision 01 (28 May 2026).
Density, non-foamed1.14 g/cm³Shore 90A
Density, 200% foaming0.57 g/cm³Shore 69A
Non-foamed density1.14 g/cm³
200% foaming density0.57 g/cm³
The density bars represent the two TDS measurements, not guaranteed reductions in the weight of any particular printed part. “200% foaming” is Kexcelled's named test condition.
Property
Non-foamed
200% foaming
Test method
Density
1.14 g/cm³
0.57 g/cm³
ISO 1183
Shore hardness
90A
69A
GB/T 531.1
Resilience
29%
23.5%
GB/T 1681-2009
Odour
Odourless
Slight odour
Manufacturer description
Mechanical Test Results at Different Print Temperatures
These results are from separate tensile tests conducted by Kexcelled on horizontally printed specimens using a Bambu Lab P1S, 100% infill, a 35°C bed and the print speeds specified in the TDS.
TDS tensile-test condition
Printed at 205°C
Printed at 240°C
Test method
Print speed
100 mm/s
45 mm/s
TDS specimen preparation
Tensile strength
14.8 MPa
6.28 MPa
GB/T 528
Elongation at break
368.7%
383.9%
GB/T 528
Values are material and specimen test results under the stated conditions. They are not design allowables or guaranteed finished-part properties. The TDS tear-test row is omitted here because its reported units require manufacturer clarification.
Example Applications
The photographs are genuine product and application images supplied by Kexcelled. The following uses are design opportunities, not approvals for regulated or safety-critical end uses.
Footwear conceptsExplore lightweight uppers, flexible structures and comfort-led product prototypes.Insoles and cushioningPrototype flexible support geometry and assess printed softness under actual loading.Accessories and product designInvestigate textile-like surface finishes and compliant decorative structures.
Frequently Asked Questions
How is TPU Air different from conventional TPU filament?
THE K8™ TPU Air is designed to foam under suitable printing conditions, allowing a user to explore different densities, hardness levels and surface finishes with one material. Kexcelled publishes separate TDS results for non-foamed and 200% foaming states.
Does printing at a higher temperature always produce Shore 69A?
No. Shore 69A is the manufacturer's measured result for its stated foaming condition, not a guaranteed value for every printed geometry or printer. Calibrate and test for the intended use.
Can it be used for shoe insoles?
It is a material worth evaluating for insole and cushioning prototypes. Real-world comfort, durability and suitability for any intended use must be tested; no medical or orthotic certification is implied.
What settings should I start with?
Use the TDS guidance of 200–250°C nozzle temperature, 30–50°C bed temperature and 50–100% fan cooling with a 0.4 mm nozzle. The manufacturer provides 100 mm/s for non-foaming and 45 mm/s for its 200% foaming condition.
Is there any odour when TPU Air foams?
The TDS describes the non-foamed condition as odourless and the foamed condition as having a slight odour. Use suitable ventilation and follow the safety data sheet.